Posted on

Gas Test Equipment and Fittings

We stock Gas Test Equipment. Items available include:

Gas Pressure Test Tee Fitting, Gas Pressure Test Tee Piece Assembly, two Fulham Nozzles and one 1/4″ Female Outlet. To Facilitate Pipe work Pressure Testing.

Arctic Smoke Pellets 6 x 13g

Arctic PH Smoke Matches – Box of 12 Suitable for gas fire spillage tests, Airflow tracing, draught testing, extractor fan testing and hand-held smoke applications. Burn time of each match is about 20 seconds. Smoke volume is 2 cubic metres per match

0 to 60mbar U Gauge. Suitable for testing the operating pressure LPG and NG Gas installations. Length 80cm,

0 to 120mbar High Specific Gravity J Gauge. Suitable for pressure testing of domestic gas installations. A 10cc bottle of fluid is included with the gauge to make up small evaporation losses. Height is approximately 80cm

0 to 150mbar High Specific Gravity U gauge. Suitable for pressure testing of domestic gas installations. A 10cc bottle of fluid is included with the gauge to make up small evaporation losses. Approximate height is 96cm.

Hand bellows for charging installation pipework during pressure testing. It has a plain bore tube which fits over a suitable nozzle. The tap allows air to be released slowly, to reduce the pressure by the desired amount for the test procedure.

More Test Equipment available CLICK HERE TO BROWSE https://gasequipment.ie/product-category/gas-fittings/test-equipment/

Posted on

Cavagna 29mbar Clip on Jumbo Regulator

Cavagna Low Pressure Clip on Jumbo Regulator with a Fulham Nozzle outlet. Suitable for use with Irish Butane Cylinders together with domestic and leisure appliances such as Ovens and Hobs, Gas BBQs, Patio Heaters, Boiling Rings, Camping Stoves and some Gas Heaters. 29mbar, 2kg/hr. This regulator has an excess flow valve as required by Irish Standards. This Regulator conforms to EN16129. Enclosed information regarding Excess flow must be read prior to use

Extra discounts may be available on this product when purchasing 5 or more

Click below to shop or for more information

Posted on

Low Pressure Camping Gas Regulator

Low Pressure Camping Gas (M16x1.5) Regulator

Low Pressure Camping Gas Regulator with a Fulham Nozzle outlet. Suitable for use with Campingaz Cylinders together with smaller leisure appliances such as smaller Gas BBQs, Patio Heaters, Camping Stoves and some Gas Heaters. 29mbar, 1.1kg/hr. This Regulator conforms to EN16129.

Click below to add to cart. https://gasequipment.ie/shop/regulators/cylinder-regulators/mtr008/

Posted on

Replacement Boilers and Water Heaters

Looking for replacement gas water heaters or gas combi boiler for your mobile home? We stock replacements for Morco Water Heaters and spare parts. Parts such as Spark generators, Pilot burner assembly’s, Thermocouples and many more available. Replacement Morco Combination Boilers and Morco spare parts such as Replacement Gas Valves and Replacement Spark Generators are also available. https://gasequipment.ie/product-category/water-heaters/

https://gasequipment.ie/product-category/combination-boilers/

Posted on

Morco FEB24 Combi Boiler Range Hydraulic Assembly Unit

MCB2191 and MCB2193 for the FEB24E, FEB24ED and FEB24ED3* are no longer available.

It is now necessary to decide which parts of the hydraulic assembly need to be replaced and the unit will need to be repaired prior to re-installing into the combi boiler.

The following options are available to repair hydraulic assemblies:
MCB2257 – Hydraulic valve Kit
MCB2160 – Plate heat exchanger
MCB2335 – Washer and O ring Kit

Below lists parts within a Hydraulic valve kit (MCB2257) that are included either loose or preassembled with their availability to purchase on an individual basis;

MCB2192 – Diaphragm housing
MCB2255 – Diaphragm

Posted on

Morco Water Heaters

Morco water heater models D61E, D61B and MP6 (PRIMO6) have now been discontinued and superseded by EUP6.

New regulations came into force in recently which state that water heaters must have lower Nitrogen Oxide (NOx) emissions. This EUP6 water heater is fully compliant, meeting all of the requirements for these new regulations.

Posted on

Morco Instantaneous Water Heaters

Morco Instantaneous Water Heaters, D61B/E and the G11E are now discontinued, superseded by the PRIMO6 and PRIMO11 Respectively. The PRIMO6 has almost identical dimensions to the D61B/E and the PRIMO11 to the G11E, making them a direct replacement. The new heaters will accept the existing flues. A fitting kit PRIFK will be required for PRIMO6 installation and EUPFK for PRIMO11 installation.

Posted on

Cylinder Regulator Compliance

We acknowledge that as per Irish Standards I.S. 813:2014 +A1; 2017, Domestic Gas Installations, B.3.4.2.1 that ‘Only a regulator with over pressure or excess flow protection shall be installed’. We acknowledge that EN16129 is the current European standard for the design and manufacture of cylinder regulators, which supersedes EN12864, which is withdrawn. Since 31/12/2015 a regulator offered for sale marked with EN12864 is not compliant.

All of the regulators which we offer for domestic installations have either excess flow or over pressure protection.

Be aware that there is non compliant product on the market in abundance.

Posted on

Morco FEB24 Combi Boiler Range Hydraulic Assembly Unit

The MCB2191 complete hydraulic assembly is no longer available, we are now able to supply some of the individual components or, alternatively a hydraulic assembly repair kit for the FEB24 combi boiler range.

The following spare parts are available:

Product Code: MCB2193 – Hydraulic Assembly Repair Kit

The above repair kit includes the items below which can also be purchased separately:

Product Code: MCB2192 – Diaphragm Housing

Product Code: MCB2256 – Diaphragm and Spindle O Ring Kit

Product Code: MCB2160 – DHW Heat Exchanger

In the vast majority of cases, existing assemblies can be repaired by either the repair kit or one of the individual parts. However, the diaphragm housing is the only moulded plastic part from the hydraulic assemblies which is available. If any of the other moulded plastic parts fail, unfortunately a repair is not possible.

Instructions will be included with each repair kit to assist engineers.

Posted on

Forklift Truck Cylinders

With regard to the correspondence in circulation originating from the H.S.A. , I would like to point out that the cylinder in question is a single valve cylinder, which in most cases are used only in a cylinder exchange system(i.e. filled by bulk gas suppliers only) and are filled to 80% capacity by measuring the amount of gas by weight or volume. The multi valve forklift truck cylinders that we supply are different in that they have a fixed maximum liquid level gauge(vent valve), where 80% fill is invariably definitively indicated when a steady white mist is emitted from this valve which is open during filling, ensuring no more than 80% fill.

Posted on

2190 Piercable Gas Cartridge

Legislation regarding the 2190 pierceable Gas Cartridge changed last year where the cartridge now contains a system inside, a self sealing valve, where you are now able to remove the cartridge from the appliance without gas escaping, whereas before the gas would escape until depleted. The 2190 Pierceable Gas Cartridge which we supply, with immediate effect, conforms to BS EN417:2012 4.3.1